Roper AL2121W Washing Machine Operation Manual

The Roper AL2121W is a two-speed top-loading automatic washing machine designed for efficient cleaning of various fabrics. It features selectable water levels, temperature settings, and multiple wash cycles including Regular, Permanent Press, Knits, Soak, and Pre-Wash (on some models). This manual provides key specifications, operation instructions, and installation guidance for optimal performance.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Washing Machine 2.3. Cycle Selection 2.4. Laundry Tips 3. Installation Instructions 3.1. Remove Old Washing Machine 3.2. Installing New Washing Machine 3.3. Leveling the Machine 3.4. Electrical and Water Connections

Key Specifications

Type: Two-speed top-loading automatic washing machine
Compatibility:
- Suitable for sturdy fabrics, permanent press, knits, and delicate items
- Not recommended for items cleaned with flammable solvents
Power Source:
- Electrical: 120 V AC, 60 Hz, 15 A circuit required
- Water Supply: Hot and cold water faucets within 4 ft (1.2 m) of machine
Electrical Rating:
- Motor: 1/2 HP
- Wash Speeds: High and low agitation/spin
- Water Levels: Large, medium, small (selectable)
- Temperature Settings: Hot, warm, cold
Capacity: 3.4 cu. ft. (tub volume)
Dimensions: 27" W x 42" H x 26" D (68.6 cm x 106.7 cm x 66 cm)
Features:
- Liquid chlorine bleach dispenser
- Liquid fabric softener dispenser
- Cycle control knob with integrated temperature selector (on some models)
- Separate water level and temperature selectors (on some models)
- Agitator for thorough cleaning
Operating Conditions:
- Temperature: 34°F to 120°F (1°C to 49°C)
- Humidity: Non-condensing
Cycles:
- Regular/Normal: Adjustable wash time for heavy to light soils
- Permanent Press: Preset for synthetics
- Knits: Gentle for knit fabrics
- Soak: Brief wash followed by soak
- Pre-Wash: For heavy soils (on some models)

Operation Instructions

Initial Setup

1. Check Components: Ensure all parts are included: hoses, fill hoses, literature pack. Read all instructions before use.
2. Power On: Plug into a grounded 3-prong outlet. Ensure water supply is connected and faucets are on.
3. Configure Settings:

Select water level based on load size (Large for full loads, Small for light loads).
Choose water temperature: Hot for whites/heavily soiled, Warm for colors/permanent press, Cold for delicates.
Familiarize with controls: Cycle control knob, temperature selector (if separate), water level selector.

4. Test Run: Run an empty cycle on Regular with hot water to check for leaks.

Operating the Washing Machine

1. Sort Laundry: Sort by color, fabric type, soil level, and size. See Laundry Tips for details.
2. Add Detergent: Measure and add detergent to the basket before clothes. Use bleach dispenser for liquid chlorine bleach (up to 1 cup, diluted).
3. Load Clothes: Loosely place load in basket, not overloading.
4. Select Settings: Set water level, temperature, and cycle. Close lid.
5. Start Cycle: Pull out cycle control knob. The machine will fill, agitate, rinse, and spin. To stop, push knob in.
6. End Cycle: Remove clothes promptly to prevent wrinkling.

Cycle Selection

Select the appropriate cycle based on fabric and soil:

Regular/Normal: Sturdy items like sheets, towels; adjustable time 6-14 minutes.
Permanent Press: Synthetics; preset 10 minutes wash, cold rinse.
Knits: Knit fabrics; gentle agitation, preset time.
Soak: 4 min wash + 14 min soak, then drain/spin.
Pre-Wash: Heavy soils; 4 min wash + 12 min soak, drain/spin (no rinse).
Rinse & Spin: Extra rinse for heavily soiled loads.

Note: Machine pauses briefly during cycles for load redistribution.

Laundry Tips

Sorting: Separate lint producers from lint collectors; whites from colors; heavy from lightweight items.
Pre-Treating Stains: Treat stains immediately with appropriate remover.
Detergent Use: Use enough to hold soil in suspension; follow package directions.
Bleach: Use only on color-safe fabrics; add to dispenser, not directly on clothes.
Fabric Softener: Dilute and add to dispenser during rinse; avoid overusing.
Load Size: Do not overload; clothes should move freely.
Water Temperature: Hot for whites/heavy soils, Warm for colors, Cold for delicates/energy saving.

Installation Instructions

Warning: To reduce the risk of fire, electric shock, or injury, follow all safety precautions. Disconnect power before installation. Ensure proper grounding.

Remove Old Washing Machine

Shut off water supply and unplug power cord.
Disconnect hoses from faucets and drain.
Tilt machine to remove shipping strap if present.
Move old machine away and clean area.

Installing New Washing Machine

Unpack machine and remove shipping materials.
Place in desired location with clearance for hoses and lid opening.
Connect fill hoses: Hot to hot faucet, cold to cold; ensure screens are in place.
Attach drain hose to standpipe or laundry tub (max 96" height).
Level machine using adjustable feet.
Plug into grounded outlet; turn on water.

Leveling the Machine

Place level on top of machine.
Adjust front legs to level front-to-back and side-to-side.
Tighten locknuts against base.
Recheck level after first few loads.

Electrical and Water Connections

Ensure a dedicated 15 A, 120 V, 60 Hz grounded outlet. Use new hoses if old ones are cracked. Do not overtighten connections to avoid damage.

Connection Type	Description
Electrical	3-prong grounded plug; no extension cords
Hot Water Inlet	Connect to hot faucet; 120°F max
Cold Water Inlet	Connect to cold faucet; pressure 20-120 psi
Drain	Secure to standpipe; no siphon-back

Caution: Flush lines before connecting to remove debris. Test for leaks after installation.