Roper AL3132W Washing Machine Operation Manual

The Roper AL3132W is a large capacity, single-speed top-loading automatic washing machine designed for efficient cleaning of various fabrics. It features selectable water levels, temperature settings, and multiple wash cycles including Regular, Permanent Press, Knits, Soak, and Pre-Wash. This manual provides key specifications, operation instructions, and installation guidance for optimal performance.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Washing Machine 2.3. Cycle Selection 2.4. Laundry Tips 3. Installation Instructions 3.1. Remove Old Washing Machine 3.2. Installing New Washing Machine 3.3. Leveling the Machine 3.4. Electrical and Water Connections

Key Specifications

Type: Large capacity, single-speed top-loading automatic washing machine
Compatibility:
- Suitable for sturdy fabrics, permanent press, knits, and delicate items
- Not recommended for items cleaned with flammable solvents
Power Source:
- Electrical: 120 V AC, 60 Hz, 15 A circuit required
- Water Supply: Hot and cold water faucets within 4 ft (1.2 m) of machine
Electrical Rating:
- Motor: 1/2 HP, single speed
- Wash Speeds: Single agitation/spin speed
- Water Levels: Large, medium, small (selectable)
- Temperature Settings: Hot, warm, cold
Capacity: 3.2 cu. ft. (tub volume)
Dimensions: 27" W x 42" H x 26" D (68.6 cm x 106.7 cm x 66 cm)
Features:
- Manual-clean lint filter
- Rinse and spin cycle
- Drain and spin cycle
- Liquid chlorine bleach dispenser
- Liquid fabric softener dispenser
- Cycle control knob with integrated temperature selector
- Agitator for thorough cleaning
Operating Conditions:
- Temperature: 34°F to 120°F (1°C to 49°C)
- Humidity: Non-condensing
Cycles:
- Regular/Normal: Adjustable wash time for heavy to light soils
- Permanent Press: Preset for synthetics
- Knits: Gentle for knit fabrics
- Soak: Brief wash followed by soak
- Pre-Wash: For heavy soils

Operation Instructions

Initial Setup

1. Check Components: Ensure all parts are included: hoses, fill hoses, literature pack. Read all instructions before use.
2. Power On: Plug into a grounded 3-prong outlet. Ensure water supply is connected and faucets are on.
3. Configure Settings:

Select water level based on load size (Large for full loads, Small for light loads).
Choose water temperature: Hot for whites/heavily soiled, Warm for colors/permanent press, Cold for delicates.
Clean the lint filter: Lift up agitator barrel, rinse the filter under water, snap agitator back.

4. Test Run: Run an empty cycle on Regular with hot water to check for leaks.

Operating the Washing Machine

1. Sort Laundry: Sort by color, fabric type, soil level, and size. See Laundry Tips for details.
2. Add Detergent: Measure and add detergent to the basket before clothes. Use bleach dispenser for liquid chlorine bleach (up to 1 cup, diluted).
3. Load Clothes: Loosely place load in basket, not overloading.
4. Select Settings: Set water level, temperature, and cycle. Close lid.
5. Start Cycle: Pull out cycle control knob. The machine will fill, agitate, rinse, and spin. To stop, push knob in.
6. End Cycle: Remove clothes promptly to prevent wrinkling. Clean lint filter after every load.

Cycle Selection

Select the appropriate cycle based on fabric and soil:

Regular/Normal: Sturdy items like sheets, towels; adjustable time 6-14 minutes.
Permanent Press: Synthetics; preset 10 minutes wash, cold rinse.
Knits: Knit fabrics; gentle agitation, preset time.
Soak: 4 min wash + 14 min soak, then drain/spin.
Pre-Wash: Heavy soils; 4 min wash + 12 min soak, drain/spin (no rinse).
Rinse & Spin: Extra rinse for heavily soiled loads.
Drain & Spin: Removes excess water without washing.

Note: Machine pauses briefly during cycles for load redistribution.

Laundry Tips

Energy Saving: Use washer during non-peak energy hours. Use hot water only for heavily soiled loads. Use cold rinses.
Sorting: Separate lint producers from lint collectors; whites from colors; heavy from lightweight items.
Pre-Treating Stains: Treat stains immediately with appropriate remover.
Detergent Use: Use enough to hold soil in suspension; follow package directions.
Bleach: Use only on color-safe fabrics; add to dispenser, not directly on clothes. Do not use chlorine bleach on non-colorfast items.
Fabric Softener: Dilute and add to dispenser during rinse; avoid overusing.
Load Size: Do not overload; clothes should move freely.
Water Temperature: Hot for whites/heavy soils (up to 120°F), Warm for colors, Cold for delicates/energy saving.
Lint Filter: Clean after every load to prevent buildup.

Installation Instructions

Warning: To reduce the risk of fire, electric shock, or injury, follow all safety precautions. Disconnect power before installation. Ensure proper grounding. The washer must be installed on a floor that can support its weight.

Remove Old Washing Machine

Shut off water supply and unplug power cord.
Disconnect hoses from faucets and drain.
Tilt machine to remove shipping strap if present.
Move old machine away and clean area.

Installing New Washing Machine

Unpack machine and remove shipping materials.
Place in desired location with clearance for hoses and lid opening (at least 1" behind, 4" sides).
Connect fill hoses: Hot to hot faucet, cold to cold; ensure screens are in place and tighten fittings.
Attach drain hose to standpipe or laundry tub (max 96" height, min 30" to prevent siphoning).
Level machine using adjustable feet.
Plug into grounded outlet; turn on water and check for leaks.

Leveling the Machine

Place level on top of machine.
Adjust front legs to level front-to-back and side-to-side.
Tighten locknuts against base.
Recheck level after first few loads; some floor unevenness is acceptable.

Electrical and Water Connections

Ensure a dedicated 15 A, 120 V, 60 Hz grounded outlet. Do not use extension cords. Water pressure: 20-120 psi. Use new hoses if old ones are cracked. Flush lines before connecting to remove debris.

Connection Type	Description
Electrical	3-prong grounded plug; no extension cords; grounded circuit required
Hot Water Inlet	Connect to hot faucet; 120°F (49°C) max; run hot water before to clear lines
Cold Water Inlet	Connect to cold faucet; pressure 20-120 psi
Drain	Secure to standpipe; ensure no siphon-back; height 30-96"

Caution: Test for leaks after installation. Protect from freezing temperatures.

Troubleshooting

No Water Entering: Check faucets on, hoses not kinked, screens clean. Run hot water before to clear lines.
Washer Does Not Drain: Check drain hose for clogs or improper height. Clean lint filter.
Excessive Vibration: Level the machine properly. Do not overload. Check shipping bolt removal.
Water Leaks: Check hose connections, fill valve, or tub seal. Tighten fittings.
Lint on Clothes: Clean lint filter after every load.
Stains on Tub: Run hot water cycles occasionally; iron/manganese in water may cause orange stains—do not use chlorine bleach.
Washer Stops Mid-Cycle: Lid not closed fully, or power interruption. Ensure child lock not engaged if applicable.
Noisy Operation: Unbalanced load—redistribute clothes. Foreign objects in tub.