Roper RAB6233P Washing Machine Operation Manual

The Roper RAB6233P is a two-speed top-loading automatic washing machine designed for efficient cleaning of various loads. It features selectable water levels, temperature options, and cycles including Heavy, Normal, Permanent Press, Knits/Delicate, Rinse and Spin, and Drain and Spin. This manual provides key specifications, operation instructions, and installation guidance for optimal performance.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Washing Machine 2.3. Cycle Selection 2.4. Laundry Tips 2.5. Troubleshooting 3. Installation Instructions 3.1. Remove Old Washing Machine 3.2. Installing New Washing Machine 3.3. Leveling the Machine 3.4. Electrical and Water Connections

Key Specifications

Type: Two-speed top-loading automatic washing machine
Compatibility:
- Suitable for cottons, linens, permanent press, synthetics, knits, and delicates
- Not recommended for items cleaned with flammable solvents or fiberglass materials
Power Source:
- Electrical: 120 V AC, 60 Hz, 15 A circuit
- Water Supply: Hot and cold water faucets within 4 ft (1.2 m), 20-120 psi
Electrical Rating:
- Motor: 1/2 HP
- Wash Speeds: High/low agitation and spin
- Water Levels: Extra small, small, medium, large (selectable)
- Temperature Settings: Hot-cold, warm-cold, cold-cold
Capacity: Large capacity (3.4 cu. ft. tub volume)
Dimensions: 27" W x 42" H x 27" D (68.6 cm x 106.7 cm x 68.6 cm)
Features:
- Liquid chlorine bleach dispenser
- Manual clean lint filter (in agitator)
- Cycle control knob with load size selector
- Temperature selector
- Agitator for thorough cleaning
Operating Conditions:
- Temperature: 32°F to 120°F (0°C to 49°C)
- Humidity: Non-condensing
Cycles:
- Heavy: 14 min wash, high speeds for heavy soils
- Normal: 12 min wash, high spin for cottons/linens
- Permanent Press: 10 min wash, cool-down rinse, low spin
- Knits/Delicate: 8 min wash, reduced agitation/low spin
- Rinse and Spin: Extra rinse/high spin
- Drain and Spin: Drain/high spin only

Operation Instructions

Initial Setup

1. Record Information: Note model/serial numbers (under lid), purchase date, dealer details.
2. Power On: Plug into grounded 3-prong outlet; ensure faucets are on.
3. Configure Settings:

Check hot water temperature (130°F/54°C min); use thermometer if needed.
For hard water (>8 grains/gallon), consider softener or extra detergent.

4. Test Run: Run empty Normal cycle with hot water to check for leaks.

Operating the Washing Machine

1. Sort Laundry: By soil, lint, color, fabric; see Laundry Tips.
2. Add Detergent: Measure and add to washer before clothes; optional color-safe bleach.
3. Add Bleach: Up to 1 cup liquid chlorine to dispenser (dilutes automatically).
4. Load Clothes: Loosely to top half of basket.
5. Select Settings: Load size, temperature, cycle; close lid.
6. Start Cycle: Pull out Cycle Control Knob; add softener during final rinse if needed.
7. End Cycle: Remove promptly; clean lint filter after each load.

Cycle Selection

Select based on fabric and soil:

Heavy: Heavily soiled heavy fabrics; 14 min, high agitation/spin.
Normal: Cottons/linens; 12 min, high spin.
Permanent Press: Synthetics; 10 min, cool-down rinse, low spin; pauses normal.
Knits/Delicate: Delicates/knits; 8 min, reduced agitation/low spin.
Rinse and Spin: Extra rinse/high spin for soiled/special items.
Drain and Spin: Remove water; high spin, no fill.

Note: Washer fills to selected load size; pauses in some cycles.

Laundry Tips

Sorting: Separate by soil, lint type, color, fabric; pretreat stains.
Loading: Loosely to 1/2 basket; mix sizes; avoid overload.
Water Temperature: Hot for heavy soils (130°F+), warm for most, cold for energy savings/light soils.
Detergent: Measure per load; use more for hard water.
Bleach: Chlorine for whites (dispenser); color-safe alternative.
Fabric Softener: Dilute and add during rinse; avoid mixing.
Energy Saving: Full loads, cold rinses, off-peak use.
Special Items: Use mesh bags for delicates; extra rinse for blankets; avoid washing feather pillows.

Troubleshooting

Washer Won't Run: Check power cord, fuse/breaker, lid closed, knob pulled out.
No Water: Faucets on? Hoses kinked/clogged? Drain hose height.
Excessive Vibration/Noise: Redistribute load; level machine; normal pauses.
Doesn't Drain: Check drain hose height/clogs.
Poor Cleaning: Overload, wrong cycle/temp, insufficient detergent.
Persistent Issues: Call 1-800-447-6737 with model details.

Installation Instructions

Warning: To reduce risk of fire, electric shock, or injury: Have qualified person install; level on supportive floor; ground properly; connect to correct water/drain; protect from weather/freezing; unplug before servicing; do not tamper with controls.

Remove Old Washing Machine

Shut off water faucets and unplug power cord.
Disconnect inlet and drain hoses.
Remove shipping materials if present.
Clean installation area; remove lid to prevent child entrapment if discarding.

Installing New Washing Machine

Unpack and remove shipping materials.
Place in location with clearance for hoses/lid.
Connect inlet hoses to hot/cold faucets (ensure screens/washers in place).
Attach drain hose to standpipe (higher than water level, max 96").
Level the machine.
Plug into grounded outlet; turn on water and check for leaks.

Leveling the Machine

Place level on top of machine.
Adjust front and rear feet for even contact with floor.
Tighten locknuts against base.
Recheck after first loads.

Electrical and Water Connections

Ensure dedicated 15 A, 120 V, 60 Hz grounded outlet. Water pressure 20-120 psi. Flush lines before connecting.

Connection Type	Description
Electrical	3-prong grounded plug; no extensions
Hot Water Inlet	Hot faucet; 130°F max; run to clear air
Cold Water Inlet	Cold faucet; 20-120 psi
Drain	Standpipe; 30-96" height; secure to prevent siphon

Caution: For winter storage: Drain hoses, add RV antifreeze to basket, run drain/spin; flush before reuse. Call 1-800-447-6737 for service.